11CIRCUIT BREAKER(TRIP BREAKER FOR THECIRCUIT YOU WILL BEWORKING ON)FUSE BOX(REMOVE FUSE FOR THECIRCUIT YOU WILL BEWORKING ON)• The blades in each
10Step 15. Slide the switch housing cup over the threaded pipe from the switch housing. Assure that no wires are pinched.Secure the cup
11® 3W-84 WALL CONTROL PREPARATIONWALL CONTROL AND HARDWARE (not to scale)Switch MountingScrews (2)Wall Plate Screws(2) White(2) AlmondWhite Wall Plat
12® 3Figure #5ALMONDBEZELRUBBER KEYPADFigure #6ALMONDBEZELFigure #4BEZELTABSALMONDBEZELPrepare for W-84 Wall Control installation - ContinuedSte
13® 3INSTALLING THE W-84 WALL CONTROLW-84 CONTROL INSTALLATION1. Use only the Casablanca W-84 wall control.2. Do not use any additional control with y
14® 3T o c o n t r o l t h e f a n a n d l i g h t s f r o m t w o l o ca t io n s (a t h r e e - w a y c i r c u i t ) , us e
15® 3OPERATION POWERThe button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunde
16® 3CHANGING FREQUENCY SETTINGNOTE: All fans leave the factory set to “1111”You will only have to change the dip switch settings in the remote
17® 3AUTOMATIC DEMONSTRATION PROGRAMA multi-tone signal will verify the start of the test pro-gram which proceeds as follows:• Lights slowly increase
18® 3OPERATION HOME-SAFE® PROGRAMThe Home-Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times.To e
19® 3IN THE WALL BEZEL REPLACEMENTWALL CONTROL AND HARDWARE (not to scale)Switch MountingScrews (2)Wall Plate Screws(2) White(2) AlmondWhite Wall Plat
2Calculation of 32°Use the tear-off Ceiling Angle Template card inserted in the back of this manual, it provides you with a simple ‘go’ or ‘no-go’ for
20Figure #4Figure #3WHITEBEZELALMONDBEZELRUBBER KEYPADRUBBER KEYPADLOCATINGPINS (4)LOCATINGPINS HOLES(4)W-84 Wall Control Bezel replacement: -
21W-84 Wall Control Bezel replacement: - CONTINUEDStep 1e. To attach the bezel back on to the front of the switch you will need to align the four (4)
2222Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.TROUBLESHOOTING TIPSThis device comp
23Fan Finishes• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the nish.• A vacuum cleaner brush nozzle can rem
3Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here
4MOTORCOUPLINGTAPEREDTHREADMOTORWIRESGROUNDWIREStep E. Using the provided allen wrench, loosen the allen set screw. Thread the downrod into the motor
5ADDITIONAL HARDWARE21/4” x 8-32 ROUNDED HEAD SCREW (2)FLAT WASHER (2)1” x 8-32 ROUNDED HEAD SCREW (2)JOISTCEILINGWIRINGCROSSBAR MOUNTING BRACKETFLATW
6Step 4. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/2” long canopy screws and lock washers provided with your Casa
7Step 5. To hang the fan body in the canopy, hold the fan body firmly and insert the nylon ball into the canopy opening. Rotate fan body until slot on
8CANOPYCOVERStep 11. Take the two pieces of the canopy cover and assemble them around the downrod as shown. Using the four screws removed in S
9Step 13. Attach the blades to the blade holders by aligning the screw holes of the holder with the holes of the blade.Attach the blade holder using t
Comments to this Manuals