PN C3143001-AT0209Ho l l i s t o n®C31UxxZFOR MODEL:OWNER’S MANUAL761 Corporate Center DrivePomona, California 917681.888.227.2178www.casablancafanco.
8LAG SCREW INSTALLATIONCANOPY INSTALLATIONNOTE: This step is required only under two conditions: If the fan weighs 36 lbs. or more or if the existing
9Ho l l i s t o n™FAN PREPARATION (not to scale)IMPORTANT SAFETY INFORMATION:Before starting the installation of your ceiling
10Step 4c. Slide both the hanging adapter cover and canopy cover ring on to the pole, then route the wires through the 3.5" Perma•Lock
11Ho l l i s t o n™Step 4e. Slide the hanging adapter cover down over the motor coupling as shown in Figure #6, making sure that the adapter cov
12Step 7. Attach the fan wires to the ceiling xture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wir
13Ho l l i s t o n™Washers (16)BLADE INSTALLATIONBlade Irons (5)Blade Iron Screws BLADE HARDWARE (not to scale)Blades (5) Blade Screws (16)Step 9a.
14CAUTION:Blade screws must be tightened securely before operating the fan.Figure #5FLYWHEELBlade Installation ContinuedStep 10b. Attach a blade/
15Ho l l i s t o n™SWITCH HOUSING AND END CAP INSTALLATIONSWITCH HOUSING HARDWARE (not to scale)SCREW PLUGSCREW #8-32BOTTOM
16Figure #1 Adaptor Installation: - Step 12a. Locate and remove the three #8-32 screws from the
17Ho l l i s t o n™ Adaptor Installation - Continued Step 12e. Locate the bottom cap and screw as shown i
LIMITED WA RRANTYIf purchased from our authorized dealer, this ceiling fan is warranted to the original purchaser by Casablanca Fan Company against de
18SWITCH HOUSING AND END CAP INSTALLATIONSWITCH HOUSING HARDWARE (not to scale)Adaptor AssemblySCREW PLUGSCREW #8-32BOTTOM CAPADAPT
19Ho l l i s t o n™Figure #6CENTER SHAFTADAPTERADAPTER SCREWS,#8-32(Screws 3)Figure #7Figure #8WHITEWIREBLUEWIREADAPTOR PLATECENTER SHAFTADAP
WHITEWIRE Adaptor Installation: - Continued Step 14e. Align the four screw holes on the cap with the holes on
21Ho l l i s t o n™ Adaptor Installation: - Continued Step 14g. Connect the wires of the motor to th
22® 3W-84 WALL CONTROL PREPARATIONWALL CONTROL AND HARDWARE (not to scale)Switch MountingScrews (2)Wall Plate Screws(2) White(2) AlmondWhite Wall Plat
23® 3Figure #5ALMONDBEZELPADFigure #6ALMONDBEZELFigure #4BEZELTABSALMONDBEZELPrepare for W-84 Wall Control installation - ContinuedSte
24® 3INSTALLING THE W-84 WALL CONTROLW-84 CONTROL INSTALLATION1. Use only the Casablanca W-84 wall control.2. Do not use any additional control with y
25® 3To control the fan and lights from two l o c a t i o n s ( a t h r e e - w a y c i r c u i t ) , u s e t w o W-84 wall controls
26® 3OPERATION POWERThe button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunde
27® 3CHANGING FREQUENCY SETTINGNOTE: All fans leave the factory set to “1111”You will only have to change the dip switch settings in the remo
1Ho l l i s t o n™Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; the
28® 3AUTOMATIC DEMONSTRATION PROGRAMA multi-tone signal will verify the start of the test pro-gram which proceeds as follows:• Lights slowly increase
29® 3OPERATION HOME-SAFE® PROGRAMThe Home-Safe Program makes an unoccupied home appear occupied by turning the lights on and off at random times.To e
30® 3IN THE WALL BEZEL REPLACEMENTWALL CONTROL AND HARDWARE (not to scale)Switch MountingScrews (2)Wall Plate Screws(2) White(2) AlmondWhite Wall Plat
31Ho l l i s t o n™Figure #4Figure #3WHITEBEZELALMONDBEZELPADPADLOCATINGPINS (4)LOCATINGPINS HOLES(4)W-84 Wall Control Bezel r
32W- 84 Wall Co ntr ol Be zel repl ace me n t: - CONTINUEDStep 1e. To attach the bezel back on to the front of the switch you will need to
33Ho l l i s t o n™33Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.TROUBLESHOOTING TIP
34Fan Finishes• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the nish.• A vacuum cleaner brush nozzle can rem
35Ho l l i s t o n™
2Motor Identication PlateRECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION! Please take a moment to locate the model number and serial number from
3Ho l l i s t o n™Parts GuideItem # Description Picture (not to scale) Quantity 1. Motor Housing 1 2. Ceiling plate 1 3. Phillips Screwdriver 1 4.Scre
4Item # Description Picture (not to scale) Quantity15. Blades 516. Blade Irons 517. Screw Pack (C): Blade Iron Screws (pre-installed, see pg 13, step
5Ho l l i s t o n™Circuit Breaker(Trip breaker for thecircuit you will beworking on)Fuse Box(Remove fuse for thecircuit you will beworking on)18"
6MOUNTING RECOMMENDATIONSBefore mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, an
7Ho l l i s t o n™FAN INSTALLATIONCEILING HARDWARE (not to scale)Using Existing Ceiling Fixture Outlet BoxAfter turning the power OFF at its source (e
Comments to this Manuals