Casablanca Fan Company Brescia Gallery Edition User Manual download pdf (Page 13)

INTELI•TOUCH OPERATION ♦ POWER

The button is normally left in the on position. Always turn the

power off during cleaning or servicing the fan and during thunderstorms. It

is also used to exit or enter additional programs.

POWER must be left on to retain a previously set fan speed or light level.

INTELI•TOUCH OPERATION ♦ SPEED CONTROL

There are six individual speed settings for the fan; each speed is indicated by

an audible tone of increasing pitch.

To select the desired fan speed:

1. With fan off, press and hold the button labeled

. The fan blades

will start rotating at the slowest speed, and will increase in steps.

2. Release the button when the desired speed is reached.

The fan speed is now in memory and will automatically come on at the same

speed each time the button is used. To maintain this level of speed,

turn the fan on by pressing

less than one second. To lower speed,

turn fan off, then on by pressing and holding the

button until the

desired speed is reached. When the fan is on, you may increase the speed by

pressing and holding the button until the desired speed is reached,

then release it.

FAN CONTROL

ON - OFF

A momentary press

of the FAN button

TO CHANGE SPEED

Press and hold FAN

button longer than

one second

INTELI•TOUCH OPERATION ♦ REVERSING AIRFLOW

The direction of airflow can be changed from downward to

upward or from upward to downward.

To reverse the airflow:

1. Make sure the is on.

2. Press the button.

Note: A four-toned signal indi-

cates the command was accepted

by the fan. A few seconds later

the fan will slow to a stop and

then reverse direction.

INTELI•TOUCH OPERATION ♦ LIGHT

LIGHT CONTROL

ON - OFF

A momentary press of

the LIGHT button

TO CHANGE BRIGHTNESS

PRESS AND HOLD

LIGHT BUTTON

LONGER THAN ONE

SECOND

To turn the lights off and on, press and release the button for less

than one second.

To vary the light brightness:

1. With lights off, press and hold the button. After one second

the lights come on at their lowest level and gradually become brighter.

2. Release the button when the desired brightness level is reached.

The brightness level is now in the fan memory and will automatically come

on at the same brightness the next time the button is used. To

maintain this level of brightness, press the button for less than

one second. To lower the brightness, turn the lights off, then press and hold

the button until the desired brightness level is reached. When the

light is on, you may increase the brightness level by pressing and holding

the button until the desired level is reached, then release it.

Programmed into every Inteli-Touch Series fan is an Auto-

matic Demonstration Program. It can be used to fully

demonstrate and test the operation of the fan.

To enter the demonstration program:

1. Turn off for at least three seconds. This will

clear the fan memory ready for programming.

2. Turn on.

3. Immediately operate the buttons in the following se-

quence:

FAN - LIGHT - FAN - LIGHT - FAN

A multi-tone signal will verify the start of the test program

which proceeds as follows:

• Lights slowly increase to full intensity.

• Fan accelerates to speed three with audio tones.

• Light dims to half intensity.

• Fan accelerates to full speed with audio tones.

• Fan reverses at full speed with audio tones.

• Fan operates at full speed.

• Fan power is reversed with audio tones.

• Fan turns off with audio tones (blades coast for a short

time).

• Lights turn off.

The complete cycle lasts slightly over one minute. It will

continue to repeat until the is turned off for more

than three seconds, cancelling the program.

AUTOMATIC DEMONSTRATION PROGRAM

++++++

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 21 22

Comments to this Manuals

No comments

Casablanca Fan Company Brescia Gallery Edition User Manual Page 13

Comments to this Manuals